Typical: Industrial
Ecomax ESE 100
Biodegradable stern tube lubricant
Hydraulic Fluids
Hydraulic Fluids
Ecomax ESE 100
Biodegradable stern tube lubricant
These lubricants are a range of high performance emulsifying biodegradable oils based on synthetic esters, developed primarily for use in stern tubes and bearings where water ingress may occur. The product meets the criteria in the US Coastguard Vessel General Permit (VGP) definitions for biodegradable, minimally –toxic and non-bio accumulative published by the US EPA
Ecomax ESE 150
Biodegradable stern tube lubricant
Hydraulic Fluids
Hydraulic Fluids
Ecomax ESE 150
Biodegradable stern tube lubricant
These lubricants are a range of high performance emulsifying biodegradable oils based on synthetic esters, developed primarily for use in stern tubes and bearings where water ingress may occur. The product meets the criteria in the US Coastguard Vessel General Permit (VGP) definitions for biodegradable, minimally –toxic and non-bio accumulative published by the US EPA
Ecomax ESE 220
Biodegradable stern tube lubricant
Hydraulic Fluids
Hydraulic Fluids
Ecomax ESE 220
Biodegradable stern tube lubricant
These lubricants are a range of high performance emulsifying biodegradable oils based on synthetic esters, developed primarily for use in stern tubes and bearings where water ingress may occur. The product meets the criteria in the US Coastguard Vessel General Permit (VGP) definitions for biodegradable, minimally –toxic and non-bio accumulative published by the US EPA
Ecomax ESE 68
Biodegradable stern tube lubricant
Hydraulic Fluids
Hydraulic Fluids
Ecomax ESE 68
Biodegradable stern tube lubricant
These lubricants are a range of high performance emulsifying biodegradable oils based on synthetic esters, developed primarily for use in stern tubes and bearings where water ingress may occur. The product meets the criteria in the US Coastguard Vessel General Permit (VGP) definitions for biodegradable, minimally –toxic and non-bio accumulative published by the US EPA
Ecomax XSE 46
Biodegradable hydraulic fluid
Hydraulic Fluids
Hydraulic Fluids
Ecomax XSE 46
Biodegradable hydraulic fluid
These products are a premium hydraulic biodegradable fluids environmental friendly for hydraulic systems with high temperature variations, difficult environments, for marine, industrial and automotive applications. This product is based on fully saturated synthetic esters and special additives that provide good stability over a wide range of temperatures.
FDX 100 ACA
Synthetic forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 100 ACA
Synthetic forming fluid
This product is a synthetic low viscosity water based evaporable fluid for forming applications. It is suitable for stamping, drawing of aluminium, steel, stainless steel strips and parts. The fluid is free of oils, solvents, silicones and chlorine and leaves a very thin film on the part that is compatible with paints, electroplating and welding.
FDX 1001 AM
Evaporable stamping and forming oil
Metalworking Fluids
Metalworking Fluids
FDX 1001 AM
Evaporable stamping and forming oil
This product is a low viscosity evaporating oil specially formulated for stamping and forming applications. It contains polar compounds to achieve most effective operations. It evaporates leaving very small amounts of residues, therefore degreasing of parts is not necessary.
FDX 1030 CU
Tube drawing oil
Metalworking Fluids
Metalworking Fluids
FDX 1030 CU
Tube drawing oil
This product is a neat oil specially formulated for tube drawing and forming applications of copper, bronze and aluminium. Product has very good lubricity and does not leave residues after annealing treatments.
FDX 11
Stamping and forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 11
Stamping and forming fluid
This product is an evaporating fluid with a low viscosity specially formulated for stamping and forming applications. The main advantage is that parts do not need to be degreased thanks to very little residue. It does not contain chlorine compounds.
FDX 12
Stamping and forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 12
Stamping and forming fluid
This product is an evaporating oil with a low viscosity specially formulated for stamping and forming applications. The main advantage of this product is that parts do not need to be degreased. There is very little residue left on the parts and that will evaporate within a short period of time.
FDX 172
Stamping and forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 172
Stamping and forming fluid
This product is a premium oil specially formulated for stamping and forming applications. It has a combination of E.P. additives to achieve better performance and finishing. It contains polar compounds to achieve most effective operations and better productivity.
FDX 18
Stamping and forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 18
Stamping and forming fluid
This product is a low viscosity evaporating oil specially formulated for stamping and forming applications. It has E.P. additives to achieve better performance and finishing.
FDX 180
Stamping and forming fluid
Metalworking Fluids
Metalworking Fluids
FDX 180
Stamping and forming fluid
This product is an ester based premium oil specially formulated for stamping and forming applications. It has a combination of E.P. additives to achieve better performance and finishing. It contains polar compounds to achieve most effective operations and better productivity.
FDX 20 RL
Steel quenching oil, washable
Metalworking Fluids
Metalworking Fluids
FDX 20 RL
Steel quenching oil, washable
This product is quenching oil for heat treatment of all types of steels heated with salts, electrical furnaces, or liquid fuels. It is a highly refined oil with an oxidation resistance that forms a minimum of deposits.
FDX 240 A
Stamping oil
Metalworking Fluids
Metalworking Fluids
FDX 240 A
Stamping oil
This product is an EP fortified fluid, specially formulated for aluminium stamping and drawing operations. The synergistic combination of EP additives, lubricity and polar compounds make it especially suitable for obtaining high efficiency and ultimate performance. The product does not contain chlorine compounds.
FDX 3009
Stamping and forming oil
Metalworking Fluids
Metalworking Fluids
FDX 3009
Stamping and forming oil
This product is an EP fortified fluid formulated for stamping, sheet cutting and drawing operations. The combination of EP additives, lubricity and polar compounds make it especially suitable for obtaining high efficiency and performance. Thanks to the excellent lubricant properties of this product the economic lifetime of dies and punches is increased. Furthermore, fractures and
FDX 3012
Drawing and sheet cutting oil
Metalworking Fluids
Metalworking Fluids
FDX 3012
Drawing and sheet cutting oil
This product is an oil with EP properties specially formulated for stamping, sheet cutting and drawing applications. The combination of EP additives, lubricity and polar compounds make it especially suitable for obtaining very high efficiency. Thanks to the excellent lubricating properties of this product dies and punches last longer and it will leave the surface
FDX 3020 Inox
Cold forming oil
Metalworking Fluids
Metalworking Fluids
FDX 3020 Inox
Cold forming oil
This product is an oil specially formulated to lubricate cold forming applications. It contains polar and extreme pressure (E.P.) to produce a product with the proper balancing characteristics.
FDX 410 A
Forming and wire drawing oil
Metalworking Fluids
Metalworking Fluids
FDX 410 A
Forming and wire drawing oil
This product is an oil with high content of EP additives and corrosion inhibitors to avoid aluminum surface oxidation. It has been specially formulated for forming and drawing of aluminium parts. It is also suitable for wire drawing as the specially selected additives will guarantee a bright aspect of the wire. Product does not contain
FDX 411
Stamping and drawing oil
Metalworking Fluids
Metalworking Fluids
FDX 411
Stamping and drawing oil
This product is an oil with EP properties that does not contain chlorine compounds and is especially formulated for stamping and drawing applications. The combination of E.P. additives, lubricity and polar compounds assures you high efficiency. Due to the excellent lubricant properties of, dies and punches last longer. Furthermore, fractures and scratches on the surface
FDX 442 A
Wire drawing oil
Metalworking Fluids
Metalworking Fluids
FDX 442 A
Wire drawing oil
This product is an EP fortified fluid specially formulated for aluminium wire drawing. The synergistic combination of EP additives, lubricity and polar compounds make it especially suitable for obtaining high efficiency and performance. It is chlorine free.
FDX 514
Cold forming oil
Metalworking Fluids
Metalworking Fluids
FDX 514
Cold forming oil
This product is a cold forming oil with E.P. and polar additives specially formulated for forming medium and heavy duty steel operations. Product does not contain chlorine compounds.
FDX 580
Tube drawing soluble oil
Metalworking Fluids
Metalworking Fluids
FDX 580
Tube drawing soluble oil
This product is a semi-synthetic water-soluble oil developed for the tube drawing of steel and galvanized steel. The product has been formulated to form high stable emulsions for use in individual and centralized systems.
